Machining Requests

Machining Requests

(911 - 920 from 1302 applications)

 
Custom parts
Machine Heatsink to give flat base

Posted 544d 20h ago

End: 0d 0h

0 Offer

Raw aluminium heatsink base dimension 165x100mm needs to be machined to get a very flat mirror finish base. Not sure if fly cutting may be the best method ? Wil ...

Raw aluminium heatsink base dimension 165x100mm needs to be machined to get a very flat mirror finish base. Not sure if fly cutting may be the best method ? Will post heatsink to winning supplier. CAD image of heatsink attached. Need to remove absolute minimum of material. Note that the heatsink already has 4 M4 tapped holes made in the surface to be machined.

Ianken A                                                                                    

Custom parts
acetal milling

Posted 545d 0h ago

End: 0d 0h

0 Offer

i was wondering i could get these two parts milled out of Acetal the drawings are attached regards Mohammed Dawood

i was wondering i could get these two parts milled out of Acetal the drawings are attached regards Mohammed Dawood

maldawoud85                                                                                    

Custom parts
Motor mounting

Posted 546d 2h ago

End: 0d 0h

2 Offers

simple aluminium part to be machined

simple aluminium part to be machined

henryjwood (P)                                                                                    

Custom parts
Aluminium Compartment Box

Posted 546d 9h ago

End: 0d 0h

1 Offer

I wish to have an aluminium compartment box milled. The number of trays is to be 7x4. Each tray is to be 15mmx35mmx35mm (HxWxD). The walls between the trays are ...

I wish to have an aluminium compartment box milled. The number of trays is to be 7x4. Each tray is to be 15mmx35mmx35mm (HxWxD). The walls between the trays are ideally going to be 1-2mm. The base is to have some detailing on the underside to allow heating cable to be ran back and forward to heat up the tray. The specifics of this detailing are to be confirmed. At the moment I am looking for rough quotes of how much this will cost to see if it is within budget or way above.

edcoppen                                                                                    

Custom parts
Cylinderical body of 1/18 scale model of WW2 German V2 rocket

Posted 547d 6h ago

End: 0d 0h

0 Offer

I collect 1/18 scale models of WW2 German aircraft and would like a V2 rocket. I would like to have an approximately 75 cm length of either plastic or acrylic ( ...

I collect 1/18 scale models of WW2 German aircraft and would like a V2 rocket. I would like to have an approximately 75 cm length of either plastic or acrylic (whichever is most cost effective) 9 cm diameter solid bar turned to the correct profile and scale size as the main rocket body (I will then make & attach the tail fins, rocket motor, etc myself). Attached is a screenshot showing the blueprint of a real V2 rocket to use to obtain the scale sizes, etc.

AndyWinn                                                                                    

One copy of brass ball-headed screw (#12 20tpi)

Posted 547d 18h ago

End: 0d 0h

2 Offers

Please provide one copy of an early 20th century American brass ball-headed screw (no. 12 with 20 turns per inch). A drawing (inc. photograph), with measurements taken from an original screw, is attached. The tolerance for the overall width and length of the screw is +/- 0.1mm. A 'normal' tolerance is sufficient for the thread. The ball-head should be solid brass. The rest of the screw may be brass or steel.

A                                                                                    

Custom parts
car seat pan

Posted 547d 23h ago

End: 0d 0h

0 Offer

i would like press dies(male/female) for a seat pan,i do not have drawings but have 3d scanned the part. i would like the dies to be made out of tool steel, har ...

i would like press dies(male/female) for a seat pan,i do not have drawings but have 3d scanned the part. i would like the dies to be made out of tool steel, hard enough to produce thousands of pieces. the final product is made of 1-1.2mm mild steel

brian.gikonyo (P)                                                                                    

Custom parts
Apache Upgrade

Posted 548d 5h ago

End: 0d 0h

0 Offer

Small components for a radio controlled scale model of an Apache helicopter. Preference for machining from aluminium as opposed to 3D printing unless tolerance ...

Small components for a radio controlled scale model of an Apache helicopter. Preference for machining from aluminium as opposed to 3D printing unless tolerance for threads can be achieved. Threads are indicative not ISO - will need conversion to ISO fine No measurements shown on JPEG images - hoping attached .STP files have converted correctly and will give necessary dimensional information. Scale is 1:1. 6 components in total.

borneojohn                                                                                    

Custom parts
Branding Head milling with company logo x 4

Posted 549d 0h ago

End: 0d 0h

0 Offer

We have 4 branding heads which need milling flat and then our new logo milled into the head so it protrudes by 2.5mm.

We have 4 branding heads which need milling flat and then our new logo milled into the head so it protrudes by 2.5mm.

info@jerseyoak.com                                                                                    

Custom Machined Parts

30 parts machined from graphite rod (will supply)

Posted 549day 5h ago

End: 0d 0h

1 Offer

We have a requirement for 30 parts machined from a 54mm (OD) x 609mm (Length) graphite rod. The parts have only 1 surface that requires machining. We will supply the graphite rod.

sinclag A